What're your thoughts about How to Install a Bathtub Yourself?
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old bathtub is easily accessible, the job can relocate immediately; if you have to open a wall surface to remove the old tub as well as place the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the task as well as are comfortable attempting it. Rather than hiring a service provider to take over a halfway-completed project, it is much better to take into consideration using one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This short article will certainly help you set up a brand-new tub in your restroom if you have already purchased a new tub and also don't need to alter the arrangement of your previous supply of water pipelines.
Your tools and also material list need to comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any water staying in the system. The process of getting rid of the existing faucets can be rather problematic because of the limited access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers are in location between the tap and the sink. Secure the faucet in place with the maker given backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type needs to be attached to the tap ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing both wooden boards under its feet, put the bath tub in the required placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the proper supply pipeline by making a compression join; after that do the very same for the other tap.
Switch on the water supply and examine all joints and also new pipework for leaks and also tighten them if essential. Fill the tub and also check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub must wait until the tub has been utilized at least once as this will certainly resolve it into its last placement.
Getting ready for the Installment
Firstly, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to prevent stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, bring about issues with wetness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes and cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that editorial on How to Install a Bathtub through an acquaintance on a different website. If you appreciated our blog entry please remember to share it. Many thanks for taking the time to read it.
Burst pipe? Phone!